Manual 04 - Power Button Cable

In the next few steps, you'll be opening the Kindle by freeing the clips marked in Picture 2.

Picture 1: Insert the blue pry tool directly under the charging port.

Picture 2: Slide the blue pry tool slightly left, under the headset jack.

Picture 3: Pry the battery cover open just enough to insert a guitar pick left of the headset jack.

Picture 1: Slide the blue pry tool right, under the power button.

Picture 2: Pry the battery cover open just enough to insert a guitar pick right of the power button.

Pry from the bottom of the Kindle to the top to release the battery cover clips.

Pry up the other side.

With the Kindle upside down (charging port at top), use your hands to separate the battery cover from the Kindle. Start at the charging port and work your way down.

Place battery cover in ZONE V.

Picture 1: Peel up foam tape covering the speaker connector. Place in COMPARTMENT A.

Picture 2: Wedge your fingers in the notches between the black speaker cable head and the white speaker connector. Pull the black speaker cable head free.

Use a blue pry tool if you can't fit your fingers in the notches.

Picture 3: Unthread the speaker cable.

Remove two 3.3 mm Phillips #00 screws securing the speaker assembly. Place in SLOT 1.

Remove speaker assembly and place in ZONE I.

Use the blue pry tool to disconnect the antenna cable head.

Unthread antenna cable, but don't try to remove it.

Picture 1: Wedge the spudger under the lower-right corner of the battery.

Pictures 2 & 3: Work your way up the right side.

Picture 1: Wedge the spudger under the lower-left corner of the battery as shown.

Pictures 2 & 3: Work your way up the left side.

Don't try to remove the battery as it's still connected to the logic board:

Lift the battery up from the bottom to free it from the adhesive.

Lift it to a 45° angle.

Disconnect the battery:

Pictures 1 & 2: Wedge the pointed end of the spudger on either side of the battery connector to unhook it.

Picture 3: Make sure both sides are unhooked while pulling the battery up and away from the Kindle. Place the battery in ZONE V with the battery cover.

Picture 1: Use a wide blue pry tool to disconnect the LCD cable.

Picture 2: Open the ZIF connector securing the power button cable.

Picture 3: Open the ZIF connector securing the digitizer cable.

Picture 1: Remove two 2.3 mm Phillips screws holding down the digitizer cable. Place in SLOT 2.

Picture 2: Slide the digitizer cable connector out with your finger.

Picture 3: Remove six 2.6 mm Phillips screws securing the motherboard. Place screws in SLOT 3.

Pictures 1 & 2: Wedge the blue pry tool between the logic board and front panel exactly where shown. Pry just enough to pivot the logic board around the notch in the red square.

Picture 3: The bottom of the logic board is lightly adhered to the mid-plate. Wedge the wide blue pry tool exactly where shown. Gently twist counter-clockwise to lift the bottom of the board.

Picture 1: Lift the bottom edge of the logic board while sliding the power button cable free.

Picture 2: Carefully guide the charging port and headset jack (soldered to the bottom of the logic board) free.

Picture 3: Lift the logic board away from the device. Place in ZONES II & III.

Remove the 2.5 mm Phillips scew securing the power button cable. Place screw in SLOT 4.

Peel up power button cable with your fingers and place in COMPARTMENT B.

Replace power button cable from COMPARTMENT B.

From SLOT 4, replace the 2.5 mm Phillips screw to secure the power button cable.

Replace logic board from ZONES II & III. Guide the charging port and headset jack in first:

Picture 1: Shows the charging port and headset jack on the bottom of the logic board.

Picture 2: Shows the openings for the headset jack and charging port.

Picture 3: Guide the charging port and headset jack in.

Make sure the power button cable doesn't get stuck under the logic board.

Pictures 1 & 2: Seat power button cable then gently push the logic board into place. Make sure the logic board is situated under the clip marked in Picture 2.

Picture 3: From SLOT 3, replace six 2.6 mm Phillips screws.

Make sure power button cable is pushed in all the way. Close ZIF connector.

Seat LCD cable.

Picture 1: Guide digitizer cable into ZIF connector.

Picture 2: From SLOT 2, replace two 2.3 mm Phillips screws to secure the digitizer cable.

Picture 3: Close ZIF connector.

Seat the battery from ZONE V while guiding the battery connector into its socket.

Push connector in until it snaps into place.

Thread antenna along the left edge of the battery.

Seat antenna on logic board.

Replace speaker assembly from ZONE I.

Replace two 3.3 mm Phillips #00 screws securing the speaker assembly from SLOT 1.

Picture 1: Thread speaker cable through the track just left of the battery.

Picture 2: Push speaker cable connector into place.

Replace foam tape from COMPARTMENT A.

From ZONE V, secure the battery cover to the Kindle.

Start with the two tabs on either side of the charging port.

Push the bottom into place and work your way to the top.

Power up the device and test the replacement part or parts.