Manual 07 - Rear Camera

Power down device.

Use the notch above the power button to remove the battery cover. Place in ZONE V.

Remove the SIM card and SD card. Place both in Sandbox COMPARTMENT A.

Remove six 3.4 mm #00 Phillips screws from loudspeaker assembly. Place in SLOT 1.

Use the curved-tip tweezers to remove any screws that get stuck.

Pull the loudspeaker assembly away from the phone starting near the charging port.

Place loudspeaker assembly in ZONE I.

Picture 1: Remove eight 3.4 mm #00 Phillips screws. Place in SLOT 1.

Note the Samsung warranty sticker (large circle) in the upper-left corner. Remove it - there's a screw underneath.

Picture 2: Note the orientation of the phone: insert guitar pick just right of the charging port between the mid-frame and front panel.

The mid-frame is thin and weaker under the charging port.

Picture 3: Carefully work your way around the corner to release clips holding the mid-frame.

Picture 1: Move up the side of the mid-frame. Remove the guitar pick before you reach the power button.

Picture 2: Gently tug on the mid-frame with one hand to create space, then reinsert the guitar pick in the corner above the power button with the opposite hand.

Picture 3: Release the clips along the top edge of the mid-frame.

Pictures 1 & 2: Start working your way down the volume rocker side. Remove the guitar pick when you reach the volume rocker.

Picture 3: Reinsert the guitar pick below the volume rocker and work your way down.

Pictures 1 & 2: Work up the lower-right corner until you're able to wedge your fingers between the mid-frame and front panel.

Picture 3: Gently peel the mid-frame away from the front panel. Place mid-frame in ZONE V.

The power button and volume rocker are part of the mid-frame assembly.

Disconnect the cellular antenna:

Use blue pry tool to disconnect top.

Unthread antenna.

Disconnect bottom.

Place antenna in ZONE II.

Disconnect the charging port cable.

Disconnect soft keys cable.

Picture 1: Wedge flat end of spudger exactly where shown and lift slightly.

Pictures 2 & 3: Slowly work up the charging port assembly to free it from the mild adhesive holding it in place.

Place charging port in ZONE III.

Picture 1: Remove 2.4 mm #00 Phillips screw from shield (covering front-facing camera and infrared sensor). Place in SLOT 2.

Picture 2: Avoid contact with the infrared sensor as you remove the shield covering the front camera & speaker:

Picture 3: Wedge one prong of the curved-tip tweezers under the shield as shown.

Close tweezers and unhook the tab in the red square first. Continue lifting shield away from phone.

Place shield in COMPARTMENT B.

Disconnect front-facing camera with blue pry tool.

Pick up the camera with your fingers. Place front-facing camera in COMPARTMENT C.

Disconnect infrared sensor / earpiece speaker assembly with blue pry tool.

Wedge the flat end of the spudger under the infrared sensor and pry up slightly.

The earpiece speaker is wedged tightly into its slot: use your fingers to carefully peel it up just enough to wedge the spudger underneath.

Finish removing the assembly with the flat end of the spudger and place it in COMPARTMENT C.

Disconnect the headphone jack.

Use the pointed tip of the spudger to lift the headphone jack free.

Place headphone jack in COMPARTMENT C.

Picture 1: Remove one 2.4 mm #00 Phillips screw. Place in SLOT 2.

Picture 2: Disconnect display cable.

Picture 3: Disconnect volume rocker cable.

There is a small amount of adhesive under the battery contact (red square in Picture 1):

Picture 1: Wedge flat end of the spudger under the corner of the logic board. Slowly twist the spudger to free the adhesive under the battery contact.

Picture 2: Use both hands to gently guide the logic board away from the front panel.

Place logic board in ZONE IV.

Use a blue pry tool to disconnect the rear camera on the underside of the logic board.

Place rear camera in COMPARTMENT D.

From COMPARTMENT D:

Seat rear camera on underside of logic board.

From ZONE IV seat the logic board:

Make sure the display cable and volume cable aren't trapped underneath.

Picture 1: Connect volume rocker cable.

Picture 2: Connect display cable.

Picture 3: Replace one 2.4 mm #00 Phillips screw from SLOT 2.

Seat headphone jack from COMPARTMENT C, then:

Connect headphone jack cable.

From COMPARTMENT C seat earpiece speaker / infrared sensor assembly:

Seat earpiece speaker first.

Then seat infrared sensor and connect the cable to the logic board.

Replace front-facing camera from COMPARTMENT C:

Seat camera.

Connect camera cable.

From COMPARTMENT B, seat shield (over the front-facing camera and infrared sensor):

Line up opening on shield with tab on front panel.

Push shield into place until the side and back clips are hooked.

Replace 2.4 mm #00 Phillips screw from SLOT 2 to hold shield.

Seat charging port from ZONE III:

Connect charging port cable to main logic board.

Connect soft keys cable to charging port daughter board.

Picture 1: From ZONE II, seat lower end of the antenna cable on charging port board.

Picture 2: Thread cable through the groove along the right side of the outer wall of the battery chamber.

Picture 3: Connect antenna to main logic board.

From ZONE V, seat the mid-frame on the phone:

Line up the mid-frame, then:

Snap the bottom edge in place first, pushing down on either side of the charging port.

Push top edge into place.

Push sides into place.

Check the perimeter to ensure the mid-frame is fully seated.

Replace eight 3.4 mm #00 Phillips screws from SLOT 1.

Replace loudspeaker assembly from ZONE I:

Line it up then snap it into place.

Replace six 3.4 mm #00 Phillips screws securing loudspeaker from SLOT 1.

Replace the SIM card and SD card from COMPARTMENT A.

Replace the battery cover from ZONE V. Check around the perimeter to ensure all clips are snapped into place.

Power up and test device.